#Bmw e60 ccc upgrade to cic how to#
#Bmw e60 ccc upgrade to cic install#

Good job, there are two more wires left to replace. Remove red wire from the navigation socket, next insert it into hole #4 from provided socket.ДЇinally insert Red wire with the red ending from emulator harness into the same hole #15 in Navi socket. Push this wire until you will hear a вЂњclickвЂќ.Дo the same procedure with pin #15. Brown wire with yellow ending goes into PIN 12 (the same hole which you have just emptied). Now it is time to insert one of the four wires attached to emulator. When the brown wire will be out, take in hand empty socket attached to emulator harness and plug it into the hole #3. When you press the tab correctly, you should be able to remove this wire without problems. LetвЂ™s start from removing pin 12 (Ground)ДЄgain you will need small screwdriver to press down small tab on a side of the pin and in the same time start pulling out from the other side brown wire. Now you have gained access to pins (9,11,12, 15).

Using small screwdriver, press down the tabвЂ¦ Start again from вЂњsquareвЂќ socket form CCC unit and find the top of it.

#Bmw e60 ccc upgrade to cic how to#

When all the connectors will be out and as well as CCC unit, it is time to connect EMULATOR (please note that there are different types of emulators and way how to connect them).

Unscrew 4 screws securing Navigation Unit.ДЄs to big radio square connector, you need to press down tab at the bottom of big socket and lift the вЂњhandleвЂќ up. Then, remove old trim around the CCC Unit. You need to press the button and pull it straight off. Unplug 3 sockets and again place AC Unit on the side. There are two clips on the left and right, which hold this AC controller in place. Again you need to lift plastic trim with plastic pry-bar. When you remove center console trim, unplug start/stop buttonвЂ¦. Please be very careful not to make any scratches on the trim, neither break it. You can start from left side or right side. Using plastic pry-bar remove Center Dashboard trim. Insert new display screen into the hole in the dashboard and secure it back using two previously removed T10 Torx screws.Д¬ONGRATULATIONS, YOUR NEW HD DISPLAY IS ALREADY INSTALLED.Дisassembly of old CCC Navigation Unit and Installation of new CIC Unit. Also connect new power connector to the HD screen. The other end of the cable run down in the hole towards the CCC/CIC Navigation Unit. ConnectBordeaux plug into the the same color socket at the back of the HD display screen.

#Bmw e60 ccc upgrade to cic install#

It is time to install brand new HD screen connector #61119185171. This is how new CID Power socket #6113 6954526 should look like (sometimes this socket has blue color). After repining 4 wires, you need to press down plastic tab at the top of the socket. Start one by one switching wires to the holes with the same numbers:Д®ach time, when you plug new wire to the hole you need to hear a вЂњclickвЂќ. You will need new CID Power socket #6113 6954526. Once the old display will be out, you need to change pins in the power socket. You no longer need the display screen connector, so you can insulate this socket with black tape and hide inside the hole in the dashboard. Unplug power connector (black plug) and LVDS screen connector (silver plug). Take out two T10 torx screws and remove old Display Screen. Д‘0mm socket wrench to disconnect battery terminalД«EFORE YOU WILL START ANY WORK, PLEASE REMOVE CD/DVDs FROM YOUR CCC NAVIGATION UNIT AND THEN DISCONNECT NEGATIVE TERMINAL FROM THE BATTERY.Дissassembly of old CCC Navigation Display and Installation of new Central Information Display. Various small Common and Philips screwdrivers Trim removal tool вЂ“ a small plastic pry-bar